[TRX] indicates optional arg (RX or TX), RX default T|F indicates TRUE or FALSE If first char of command is '-', eg -setNR ON command is not echoed to log output.x setFilter low-freq high-freq TRX setMode mode [TRX] // mode = USB, LSB, CWL, CWU, etc. setOsc freq [TRX] // freq in Hz (float) setSampleRate rate // Hz (float) setNR T|F // on/off, RX only setANF T|F // on/off, RX only setNB T|F // on/off, RX only setBIN T|F // binaural mode, on/off, RX only setNBvals thresh // float, RX only setfixedAGC gain [TRX] // float setRXAGC T|F // on/off setRXAGCCompression lev // float setRXAGCHang dur // float setRXAGCLimit lim // float setTXAGC T|F // on/off setTXAGCCompression lev // float setTXAGCHang dur // float setTXAGCLimit lim // float setTXSpeechCompression T|F // on/off setTXSpeechCompressionGain gain // float setRXEQ // f0 dB0 f1 dB1 f2 dB2 ... fN setTXEQ // f0 dB0 f1 dB1 f2 dB2 ... fN // typical: // 0 dB1 75 dB2 150 dB3 300 dB4 600 dB5 1200 dB6 2000 dB7 2800 dB8 3600 // approximates W2IHY bandcenters setRXAGC mode // mode = agcOFF, agcSLOW, etc. setANFvals taps delay gain leak // int, int, float, float, RX only setNRvals taps delay gain leak // int, int, float, float, RX only setcorrectIQ phase gain // int, int setcorrectIQphase phase // int setcorrectIQgain gain // int setSquelch lev // float, gain, RX only; default -30dB setSquelchSt T|F // on/off, RX only setTRX trx // trx = RX|TX setRunState state // RUN_MUTE, RUN_PASS, RUN_PLAY setRXPreScl T|F // on/off setRXPreSclVal valQ // dB setTXPreScl T|F // on/off setTXPreSclVal valQ // dB setRXPostScl T|F // on/off setRXPostSclVal valQ // dB setTXPostScl T|F // on/off setTXPostSclVal valQ // dB setSWCH trx [zap] // trx = RX|TX, int (always zaps at least 1) setSpotToneVals gain freq rise fall // dB, Hz, msec, msec [-12, 700, 5, 5] setSpotTone T|F // turn on, off setFinished // shutdown gracefully setRXListen rx // tell receiver rx to listen to commands to follow setRXOn [rx] // turn currently listening receiver on, or receiver rx setRXOff [rx] // turn currently listening receiver off, or receiver rx setRXPan pos // set azimuth for currently listening receiver to pos (0...1) setAuxMixGain [gain [trx]] // set mixing level for aux inputs setAuxMixSt [flag [trx]] // set aux input mix on/off setMeterType type [trx] // set meter type for trx, default rx // types: SIG, AVG, REAL, IMAG; default SIG setSpectrumType [type [scale [rx]]] // set spectrum type, scale, which rx // types: SEMI_RAW, PRE_FILT, POST_FILT (deflt POST) // scale: PWR, MAG (dflt PWR) // which rx dflt 0 reqMeter [label] // sends entire rx or tx meter block to METERPATH reqSpectrum [label] // sends current spec snapshot to SPECPATH