-[TRX] indicates optional arg (RX or TX), RX default
-T|F indicates TRUE or FALSE
-
-If first char of command is '-', eg
--setNR ON
-command is not echoed to log output.x
-
-setFilter low-freq high-freq TRX
-setMode mode [TRX] // mode = USB, LSB, CWL, CWU, etc.
-setOsc freq [TRX] // freq in Hz (float)
-setSampleRate rate // Hz (float)
-setNR T|F // on/off, RX only
-setANF T|F // on/off, RX only
-setNB T|F // on/off, RX only
-setBIN T|F // binaural mode, on/off, RX only
-setNBvals thresh // float, RX only
-setfixedAGC gain [TRX] // float
-setRXAGC T|F // on/off
-setRXAGCCompression lev // float
-setRXAGCHang dur // float
-setRXAGCLimit lim // float
-setTXAGC T|F // on/off
-setTXAGCCompression lev // float
-setTXAGCHang dur // float
-setTXAGCLimit lim // float
-setTXSpeechCompression T|F // on/off
-setTXSpeechCompressionGain gain // float
-setRXEQ <bandspec> // f0 dB0 f1 dB1 f2 dB2 ... fN
-setTXEQ <bandspec> // f0 dB0 f1 dB1 f2 dB2 ... fN
- // typical:
- // 0 dB1 75 dB2 150 dB3 300 dB4 600 dB5 1200 dB6 2000 dB7 2800 dB8 3600
- // approximates W2IHY bandcenters
-setRXAGC mode // mode = agcOFF, agcSLOW, etc.
-setANFvals taps delay gain leak // int, int, float, float, RX only
-setNRvals taps delay gain leak // int, int, float, float, RX only
-setcorrectIQ phase gain // int, int
-setcorrectIQphase phase // int
-setcorrectIQgain gain // int
-setSquelch lev // float, gain, RX only; default -30dB
-setSquelchSt T|F // on/off, RX only
-setTRX trx // trx = RX|TX
-setRunState state // RUN_MUTE, RUN_PASS, RUN_PLAY
-setRXPreScl T|F // on/off
-setRXPreSclVal valQ // dB
-setTXPreScl T|F // on/off
-setTXPreSclVal valQ // dB
-setRXPostScl T|F // on/off
-setRXPostSclVal valQ // dB
-setTXPostScl T|F // on/off
-setTXPostSclVal valQ // dB
-setSWCH trx [zap] // trx = RX|TX, int (always zaps at least 1)
-setSpotToneVals gain freq rise fall // dB, Hz, msec, msec [-12, 700, 5, 5]
-setSpotTone T|F // turn on, off
-setFinished // shutdown gracefully
-setRXListen rx // tell receiver rx to listen to commands to follow
-setRXOn [rx] // turn currently listening receiver on, or receiver rx
-setRXOff [rx] // turn currently listening receiver off, or receiver rx
-setRXPan pos // set azimuth for currently listening receiver to pos (0...1)
-setAuxMixGain [gain [trx]] // set mixing level for aux inputs
-setAuxMixSt [flag [trx]] // set aux input mix on/off
-
-setMeterType type [trx] // set meter type for trx, default rx
- // types: SIG, AVG, REAL, IMAG; default SIG
-setSpectrumType [type [scale [rx]]] // set spectrum type, scale, which rx
- // types: SEMI_RAW, PRE_FILT, POST_FILT (deflt POST)
- // scale: PWR, MAG (dflt PWR)
- // which rx dflt 0
-reqMeter [label] // sends entire rx or tx meter block to METERPATH
-reqSpectrum [label] // sends current spec snapshot to SPECPATH
-
+// [TRX] indicates optional arg (RX or TX), RX default
+// T|F indicates TRUE or FALSE
+//
+// If first char of command is '-', eg
+// -setNR ON
+// command is not echoed to log output.
+//
+// setFilter low-freq high-freq TRX
+// setMode mode [TRX] // mode = USB, LSB, CWL, CWU, etc.
+// setOsc freq [TRX] // freq in Hz (float)
+// setSampleRate rate // Hz (float)
+// setNR T|F // on/off, RX only
+// setANF T|F // on/off, RX only
+// setNB T|F // on/off, RX only
+// setBIN T|F // binaural mode, on/off, RX only
+// setNBvals thresh // float, RX only
+// setfixedAGC gain [TRX] // float
+// setRXAGC T|F // on/off
+// setRXAGCCompression lev // float
+// setRXAGCHang dur // float
+// setRXAGCLimit lim // float
+// setTXAGC T|F // on/off
+// setTXAGCCompression lev // float
+// setTXAGCHang dur // float
+// setTXAGCLimit lim // float
+// setTXSpeechCompression T|F // on/off
+// setTXSpeechCompressionGain gain // float
+// setRXEQ <bandspec> // f0 dB0 f1 dB1 f2 dB2 ... fN
+// setTXEQ <bandspec> // f0 dB0 f1 dB1 f2 dB2 ... fN
+// // typical:
+// // 0 dB1 75 dB2 150 dB3 300 dB4 600 dB5 1200 dB6 2000 dB7 2800 dB8 3600
+// // approximates W2IHY bandcenters
+// setRXAGC mode // mode = agcOFF, agcSLOW, etc.
+// setANFvals taps delay gain leak // int, int, float, float, RX only
+// setNRvals taps delay gain leak // int, int, float, float, RX only
+// setcorrectIQ phase gain // int, int
+// setcorrectIQphase phase // int
+// setcorrectIQgain gain // int
+// setSquelch lev // float, gain, RX only; default -30dB
+// setSquelchSt T|F // on/off, RX only
+// setTRX trx // trx = RX|TX
+// setRunState state // RUN_MUTE, RUN_PASS, RUN_PLAY
+// setRXPreScl T|F // on/off
+// setRXPreSclVal valQ // dB
+// setTXPreScl T|F // on/off
+// setTXPreSclVal valQ // dB
+// setRXPostScl T|F // on/off
+// setRXPostSclVal valQ // dB
+// setTXPostScl T|F // on/off
+// setTXPostSclVal valQ // dB
+// setSWCH trx [zap] // trx = RX|TX, int (always zaps at least 1)
+// setSpotToneVals gain freq rise fall // dB, Hz, msec, msec [-12, 700, 5, 5]
+// setSpotTone T|F // turn on, off
+// setFinished // shutdown gracefully
+// setRXListen rx // tell receiver rx to listen to commands to follow
+// setRXOn [rx] // turn currently listening receiver on, or receiver rx
+// setRXOff [rx] // turn currently listening receiver off, or receiver rx
+// setRXPan pos // set azimuth for currently listening receiver to pos (0...1)
+// setAuxMixGain [gain [trx]] // set mixing level for aux inputs
+// setAuxMixSt [flag [trx]] // set aux input mix on/off
+// setCompandSt [T|F [trx]] // *** NB *** trx dflt TX!!!
+// setCompand fac [trx] // probably > 0 for RX, < 0 for TX
+// setMeterType type [trx] // set meter type for trx, default rx
+// // types: SIG, AVG, REAL, IMAG; default SIG
+// setSpectrumType [type [scale [rx]]] // set spectrum type, scale, which rx
+// // types: SEMI_RAW, PRE_FILT, POST_FILT (dflt POST)
+// // scale: PWR, MAG (dflt PWR)
+// // which rx dflt 0
+// =========================================================================
+// reqMeter [label] // sends entire rx or tx meter block to METERPATH
+// reqSpectrum [label] // sends current spec snapshot to SPECPATH
+//